Transcripts
1. Introduction: Hello guys, are you interested
in designing buildings, interior and furniture using
SketsU If the answer is yes, then this course
might be for you. In this course, we are
going to have ten projects. In the first project,
we are going to design one story
house. Look at this. In the second
project, we are going to design office buildings. Look at this. In
the third project, we are going to
design a bus stop. In the fourth project,
we are going to design a moderate and
minimalist bedroom. In the fifth project,
we are going to design a bunk bed that can
accommodate three people. In the sixth project,
we are going to design a kitchen interior. Look at this. In the
seventh project, we are going to
design a home office. In the eighth project, we are
going to design a bathroom. We are going to have
a toilet, a sink, a bathtub, and also a
small swimming pool. Next, we are also going to
design a chair and a sofa. In the last project,
we are going to design a dining table. Look at this. Then after that, we are also going to generate interior design
using Copernik AI. The process is very simple. You just need to type in the
prom and click Generate, and in less than a minute, AI is going to generate
you a virtual reality. Look at this. This is
interior design for a coffee
2. Tools & Resources: Hello, guys. Welcome
back to the course. In this video, we are going
to get to know more about all tools that we are going
to use in this course. Okay, let's get started
with the first one, SketsU. Let's click on this
link and you will be redirected to this website. SketsU is one of the most popular software
for architecture, interior design and
construction engineering. There are many things that
you can do with SketsU. For example, you can
do Tree Dmdeling. You can visualize your design, look at this, and
still many more. Let's click on Industries
and Let's like Architecture. Let's scroll down a little bit. You can create Constructions
document. Look at this. You can use pre
build treaty models, so you don't need to
design from scratch, guys. There is a treaty
warehouse where you can find and download
pre made models. You can use it and customize
it however you want. There are many third
party extensions. You can bend geometry
with a single click. You can create
photorealistic rendering. You can also generate
cost estimates by exporting reports directly from your treaty
architecture drawings. This feature is going
to be very useful, especially if you want to estimate the cost
of the project. If you want to use SketsU,
you have two options. The first option is to
download the software locally. There are two versions,
Make OS and Windows. Make sure that you download whichever version that aligns
with your operating system. For example, in my case,
I'm using MacBook. So obviously, I'm going to
download the Make OS version. And the second option
is SketsUF web. You don't need to
download anything. You are going to design the
TD model in your browser. And don't worry
you guys, SketsOp is completely free to use. Let's click on pricing, and let's scroll down a
little bit as you guys can see SketsUp
offers a free plan. Obviously, there are
some limitations when it comes to the free plan. For example, you can only export your design to these
three file types, SKP, PNG, and STL. Okay, now let's go
back to the slide, and let's move on
to the second tool. Polygont. Let's
click on this link, and you will be
redirected to this page. Polygon is a platform where you can find and download
premade three D models. And you can reuse the model. You can customize it
however you want. You can change the color.
You can change the texture. You can modify the shape. You can do whatever
you want, guys. And sometimes you don't
want to start from scratch. You want to save time, right? So finding pre made tree D models from
polygon is a great idea. There are many things that
you can find in polygon. You can find texture, for
example, a brick texture. Look at this or a
concrete texture. Look at this. Very cool, right? You can find a variety
of three D models. For example, three D models for dining room. Look at this. We have bowl, cup
models, drinking glass, dining plates, and still
many more or decorations. Look at this. Or Kitchen. Look at this. There are
many options, right? There are many free three models that you can download.
Look at this. And in this course, we
are going to use SketsUp, so we will need to download
the SketSU extension. So let's click this
and just click this. And don't worry, guys. Polygon
is completely free to use. Let's click on pricing, as you guys can see polygon
offers a free plant. This is in my local currency. Okay, now, let's go back
to the slide and let's move on to the third
tool, BIM Object. Let's click on this
link and you will be redirected to this website. Well, BIM object is very
similar to polygont. You can find many high
quality pre made treD models. There are many categories. Let's click this. For example,
constructions, doors, electrical, electronics, engineering, and
infrastructure. What else? Fabrics, flooring,
furniture, kitchen, landscaping, lighting,
medical plumbing, sanitary, and still many more. When you are searching
for the TD model, you can filter by the software, for example, in this case,
we're going to use SketsU. So let's click this.
And let's click Search. You can also type
in the keyword. So all these Tree D models are models suitable
for sketsU guys. And don't worry. BIM
object is completely free. You just need to sign up. Okay, now, let's go
back to the slide, and let's move on
to the four tool. Simlab. Let's click
on this link, and it will be
redirected to this page. We are going to use
Simlab for viewing the Tre designs in virtual
reality environment. Let's click products, and
let's like Simlab composer. You will be redirected
to this page and to integrate the three D model to virtual reality environment, you just need to download
the model from SketsUp and upload it to Simlab and it is going to
look like this, guys. Very cool, right? So the
process is very simple. And don't worry, Simlab is
completely free to use. Let's click on pricing
as you guys can see Simlab offers a free plant. Look at this. Okay,
I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
3. Drawing Basic Shapes in SketchUp: Holy guys. Welcome
back to the course. In this video, we are
going to learn how to draw basic shapes in SketsU
and not only that, we are also going to
set exact measurements to make sure the shape is
symmetrical and proportional. Okay, now, let's get started. Firstly, click Start modeling, and you will be
redirected to this page. It might take few seconds
to load, so just wait guys. Hopefully, it doesn't
take too long. And let's click start modeling. Let's get started, guys. Firstly, I'm going to
remove this present. So let's click on the Eraser
tool and let's remove it. Make sure that you pay
very close attention to this video because it is very important for you to
understand the basic concepts. Okay, firstly, we are going
to draw a straight line. Let's click on the pencil icon, and let's draw a straight
line. It is very easy. Look at this. And I'm going to draw another
straight line. Here we go. Very easy, right? Next, we are going
to draw a rectangle. Let's click on the
rectangle icon right here, and let's draw the rectangle. I'm going to put it right here. Okay, so here is the rectangle. If you want to set exact
measurement for this rectangle, all you need to do is
to type in the number. For example, I want the
dimension to be 50. So just type in 50 guys, and let's hit Enter.
Okay, here we go. Okay, next, we are
going to draw a circle. Let's click on circle icon. If you are not able to
find this circle icon, just click this and
just click circle. And I'm going to draw
the circle right here. If you want to set
radius for the circle, just type in the number. For example, 25, and
let's hit Enter. Okay, now the circle
is getting smaller. Next, we are going
to draw a polygond. Let's click this
and let's select polygond I'm going to draw
the polygon right here. And if you want to set exact measurement
for this polygon, just type in any
number that you want, for example, 35, and
let's hit Enter. Now the polygon is
getting smaller. Next, we are going to change
the color of the shape. For example, I'm going to change the color of the
rectangle to blue. Let's select the
rectangle and let's click Matrials and I'm
going to select blue, and let's click
on the rectangle. Now the color is dark blue. Next, we are going to change
the color of the circle. Let's select the circle and
let's click on Materials and I'm going to change
the color to brown. Let's click on the circle. Now the color is brown. And lastly, we are going to change the color of the polygon. Let's select the polygond Make sure that you unselect the circle because if you are
still selecting the circle, then the color will also
be applied to the circle. We don't want that to happen. Let's click matrials
and I'm going to change the color to black. Let's click this and let's
click on the polygon. Now the color is black. Okay, guys, we have successfully changed the color of the shapes. I think that's it. That's
all you need to know. I'll see you guys in
the next video. Bye.
4. Creating 3D Objects in SketchUp: Hello, guys. Welcome
back to the course. In this video, we are
going to learn how to create basic three
D models in SketsU. Well, actually, it is very easy. I'm going to teach
you step by step. Okay, firstly, we are going
to create a cube or a beam. So let's get started
with a rectangle. So let's select the
rectangle tool. And let's create a
rectangle right here. Okay, next, we are going to use pull and push tools.
So let's click this. And let's pull this up. Okay, now we have a beam. Look at this. You can pull
it. You can also push. Okay, next, we are going
to create a cylinder. Actually, the process
is very similar guys. We are going to get
started with a circle. Let's click this and
let's click Circle. I'm going to draw a
circle right here. Not too small, but
also not too big. And let's use the
pull and push tool. So let's click this, and
we're going to pull it up. Okay, now we have a
cylinder, very cool, right? Next, we are going
to create sirs. Okay, let's get started
with a small rectangle. So let's create a small
rectangle right here, and we are going to utilize
push and pull tool. So let's click this and let's
pull this up a little bit. And let's create
another rectangle. Make sure it has the same size. And we are going to use the
push and pull tool again. And let's pull this
up a little bit. And let's do the same
thing over and over, guys. Let's create another rectangle. Make sure the size is the same. And we are going to use the
push and pull tool again. So let's pull this up. Okay, we are going
to create two more. Let's repeat the
process two more times. So let's create
another rectangle. Make sure the size is the same, and we are going to use
the push and pull tools. And let's pull this
up a little bit. And let's do it once again. Let's create another rectangle. And we are going to use
the push and pull tools, and let's pull this
up a little bit. Okay, now we have five
stairs. Very cool. If you want to
download this design, just click this and just Export, and there are many file formats like whichever file
format that you want. And you can also download
this design as an image. I'm going to select PNG. And let's click Export as PNG. It will take few seconds, maybe five or 10 seconds. Okay, we have successfully
downloaded this image. Okay, guys, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
5. Move, Rotate, Scale, Group, and Component: Hello, guys. Welcome
back to the course. In this video, we are going to learn the basic tools like move, rotate, scale group
and components. It is very essential
for you to understand these basic tools and
also know when to use it. Okay, now, let's get started. I'm going to remove this person. So let's click on the eraser
tool and let's remove him. Okay, next, we are going
to create three objects. Firstly, I'm going
to create a cube. Let's get started with a square and we are going to utilize
push and pull tools, and let's pull this up. Okay, now we have
a cube. Very cool. Next, we are going to
create a triangular prism. We are going to create
a triangle first, and we're going to use
push and pull tool. Okay, let's draw a triangle. Okay, here is the
triangle and we are going to use push pull tool. Let's pull it up. Okay, now
we have a triangular prism. Let's create another
tried object. We are going to create
a small cylinder and it's going to
look like a pipe. We are going to get started
with a very small circle. Let's click circle. Okay, now we are going to use
push pull tool. But before that, make sure that you already selected the circle. And let's pull this up. Okay, now we have a small pi. Let's talk about the first tool. The name of the tool is move. Look at this icon. You can use Move tool for repositioning
objects or geometry. For example, if you want to move a cube from the left
side to the right side, you can use this tool. Okay, let me show
you how to do it. Firstly, make sure that
you select the object. In this case. We are
going to select the cube. And let's click Move tool. And you can move the
cube to the left. You can move it to
the right. You can move it to the bottom. You can move it to
the top. You can do whatever you want, guys. It is very easy, right? Okay, now let's talk
about the second tool. Rotate. This is
rotate icon, guys. You can use Rotate tool for turning objects
around a pivot point. For example, you can rotate a ceiling fan 90 degrees to align it with
the room layout. Okay, now let me show
you how to use it. Firstly, you will need to select the object that you
want to rotate. In this example, we are going to rotate this triangular prism. Let's like these objects. Next, I'm going to click
on the Rotate icon, so let's click this Okay, now we are able to rotate
the triangular prism. Look at this. Very cool, right? Okay, I'm going to put it back
in its original positions. And now let's talk
about the turtle scale. This is the icon guys. You can use scale for resizing objects proportionally
or done proportionally. For example, you can scale
the size of this pipe so it can accommodate larger
volume. Okay, let's do it. Firstly, you will need
to select the pipe, and let's click Scale. Okay, I can make it larger. I can make it smaller.
Look at this. And the size is
proportional, guys. Okay, I'm going to make bigger. Here we go. Okay, now let's
talk about the fourth tool. The name of the tool is group. You can use group for combining multiple elements into
a single editable unit. For example, you want to group these three
objects together. So when you move the object, it will move all of these three. You don't need to
move it one by one. Okay, now let me show
you how to do it. The first thing that
you need to do is to select all these three objects. Next, we are going to
click on this icon, and let's type in group. And we are going to
click Make Group. But before that, just make sure that you have selected
all these three objects. Okay, let's click this. As you guys can see, we have successfully grouped
these three objects. So if I want to
move these objects, I don't need to
do it one by one. I just need to click Move, and if I move it to the
left or to the right, all these three
objects will follow. Okay, now let's talk
about the last one. Component. You can
use component for creating reusable
editable elements. For example, you
can create a window as a component and
place it in all rooms. When you update one,
all identical windows will be updated automatically. So it's going to make
your work easier because you only need to update once
and the others will follow. Okay, let me show
you an example. Let's say we are going
to create two circles. This is the first circle, and
this is the second circle. I'm going to make
the size the same. Well, actually, this
is a little bit smaller compared to the first
circle, but that's fine. We're going to block
these two circles, and let's click on
the search icon and let's type in component. And let's click Make component. And you will need to
name your component. In this case, I'm going
to name it component one, and let's click Create. Okay, now we have
two components. So if you update
one of the circles, the other one will follow. Okay, guys, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
6. Importing Pre Made 3D Model From SketchUp 3D Warehouse: Hello, guys. Welcome
back to the course. In this video, we are going
to learn how to import premade Tre models from
SketsUTD warehouse. Sometimes you don't want to
start from scratch, right? If you already have
a premade models, it is going to make your
work easier and also faster. Okay, now let's click
Three D Warehouse. And it is going to
open this page. And you just need to
type in the keyword. For example, in this case, I'm looking for a bet. So let's type in bet and let's click on
the search button. Okay, now it is going to
display the search result. And let's scroll
down as you guys can see, there are many options. Look at this. Okay, I'm
going to select this one. Before downloading this model, I'm going to click C Materials. Okay, now it is going to display the materials
in this model. We have Leaf, piece Lily. Okay, just click Download. Let's click by clicking here, I accept the above terms. And let's click Import. Okay, now it is
downloading the model. It will take few seconds, maybe ten or 15 seconds, depending on the
size of the file. In this case, it is 21 MB, so it is not that big. Okay, here is the bet. Very cool. Now we have a bet. And we are going to
rotate this bed. Okay, very cool. I'm going to put it right here. So we have this person
standing next to the bed. Okay, now we are going to
import another three D model. So let's click on the
Tree D warehouse, and we are going to search for another premade three D objects. In this case, I'm going to
find and import a table. So let's type in Table, and let's click
the search button. As you guys can see, we have many table here. Look at this. We have dining table. We
have a very simple table. Look at this. Okay, I'm
going to pick this one. So let's click Download. Okay, now it is
downloading the model. It only took a few seconds, maybe just 3 seconds. Okay, here we go.
Here is the table. I'm going to put the table
very close to the bed. And it seems the table
size is too big. So what I'm going to do next
is to scale this table. So I'm going to select D table, and I'm going to click scale, and I'm going to make the
size a little bit smaller. Okay, here we go. Okay, guys, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
7. Designing One Story House with SketchUp: Hello, guys. Welcome
back to the course. In this video, we are going
to start the first project. We are going to create a simple one story house with
windows and a front door. The design is going
to be very simple. I'm not an architect, so the design is not going to be very aesthetic or luxurious. I'm really sorry, guys. I hope you understand. Okay, now, let's get started. Firstly, we are going
to remove this present. Let's click on the eraser
icon. And let's remove him. Next, we are going to create a big rectangle.
Okay, here we go. And let's create a beam. Let's click Push Pul too, and let's pull this up. Let's create another
rectangle on the front. Okay, here we go. And let's create another beam. So let's click Push Pul too. I'm going to make this a little bit shorter compared
to the first one. Now we are going to create
the roof for this house. So let's scrap the pencil. I'm going to erase this. Okay, here we go. Next, we are going to create
a front door. It's going to be
very simple, guys, click on the rectangle and let's create the front
door right here. Let's use the push pull tool. It's going to look like this. This is the front door. Now we are going to create the window. The shape of the
window is circle, so I'm going to select circle, but if you want to use rectangle,
it's totally up to you. You can use any
shape that you want. Here is the window, and I'm going to create
the second one here. Make sure the size is the same. And let's use postpone two. Okay, next, we are going
to create another window. The shape of the
window is rectangle. So let's click this and I'm going to put the
window right here. And let's use post pull tool. Okay, here is the window. Next, we are going to
create a car garage. So let's create another
rectangle right here. Let's use post portal, and we're going to post this. Okay, here is the car garage. Okay, we have three windows. We have one front door
and we have car garage. Next, we are going to change
the color of the house. So let's select the roof, and I'm going to change
the color to brown. Let's click materials, and
I'm going to select brown. Okay, now the color of the roof is brown, as you
guys can see here. Next, we are also going to
change the color of the wall. It is still white. We are going to change the color
to light gray. So make sure that you select both sides and let's click gray, and let's apply the color. Okay, now we have
successfully changed the color from white to gray. And lastly, we are going
to group these objects. So make sure that you select all objects And let's
click on the search icon, and let's type in Group. And let's click Make Group. Okay, we have successfully
group all of these objects. Okay, guys, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
8. Designing Office Buildings with SketchUp: Hello guys. Welcome
back to the course. In this video, we are going
to start the second project. We are going to design office
building using SketsU. Okay, now, let's get started. Firstly, I'm going to
remove this present. And let's create a rectangle. And let's pull posto, and let's pull this up. Okay, now we are going to add
windows to this building. Let's rectangle. I'm going to create
multiple windows, maybe four or five. I want to make sure the
size is exactly the same. I'm going to copy and
paste this rectangle. We're going to do
it multiple times. As you guys can see, I
have added five Windows, one, two, three, four and five. All you need to do is to
select the first window and copy and paste
it four times. If you are using Windows, just press Control C, Control F. If you
are using Macbook, just press Comment C
and Command f. Okay, now we are going to modify
the shape a little bit. So let's select the first window and we are going to
use Push Pull tool. Let's click this and we are
going to push this inward. And we are going to do the
same thing for other windows. We are going to do the same
thing for the third windows. We are going to do the same
thing for the fourth windows. Okay, next, we are going to create a front door right here. So let's create a
small rectangle. I'm going to put it right
here and we're going to use Pospto Make sure that you
select this rectangle, not the other rectangle. And let's push this inward. Okay, now we have
the entrance door, and let's create another shape. I'm going to select circle. Well, actually, I'm going
to create a half circle, not a full circle, guys. And let's like the circle, and let's use push pull tools, and we're going to pull this up. Okay, so this is a helipad, so a helicopter can
land here, guys. That's very cool, right? Well, we're going to make
this a little bit shorter. And let's create another door. Let's create a small
rectangle right here. And let's select that rectangle, and let's push this
a little bit inward. Okay, so that's the door. Next, we are going to add another component
to this building. So let's draw a smaller
rectangle right here. And let's like this rectangle, do not select the whole
rectangle, right? Just like this rectangle, and we're going to use to make this a little
bit taller, right? So it looks like a tower. Okay, maybe not that tall. Okay, next, we are
going to create another building next
to this building, and we're going to
create a bridge connecting the first building
to the second building. Okay, for the second building, we're going to build a
very simple building. Let's draw a rectangle. Let's select that rectangle, and let's use push pull too. Okay, so here is the
second building. Okay, I'm going to
zoom out a little bit because the size of these
buildings are huge, so you can get a
better overview. Okay, this is the
second building. We are going to create
a giant window here, and we're going to
add different color. So let's click Materials, and I'm going to select blue. Okay, now we are going to
build a bridge connecting this building with
the second building. So let's create a
small rectangle. And let's select that rectangle. And we are going to
use push pull tool. Okay, so now we have
a bridge connecting the first building with
the second building. By the way, we also need to add entrance door for
the first building. So let's draw a small
rectangle right here. And let's like that rectangle, and we're going to
use Post Bo tool. Okay, here we go. We
have the entrance door. Okay, guys, we have successfully boilt two office buildings. If you want to add color, feel free to do it, guys. I think that's it. That's
all you need to know. I'll see you guys in
the next video. Bye.
9. Designing Bus Stop with SketchUp: Hello, guys. Welcome
back to the course. In this video, we are going
to design a bus stop. We are going to have
multiple chairs so the passengers can
wait and sit there, and we are also going
to have a trust can. Okay, now, let's get started. Let's draw a rectangle,
a big rectangle. Let's select this rectangle, and we are going to
use Puss Ball tool, and let's pull this
up a little bit. Let's draw another rectangle. And let's like this rectangle, and we are going to
utilize Puss Pot, and we're going to
push this inward. Okay, here we go. Next, we are going
to create a chair so the passengers can sit there
while waiting for the bus. Let's create another rectangle. And let's like this rectangle, guys, and let's
use Puss Pul tool. And let's draw
another rectangle. Just a small one, guys. Let's like this rectangle. And let's use pushbllTol again and we're going to
pull this up a little bit. Now it is a fully
functioning chair, so you can sit there and relax
while waiting for the bus. Next, we are going
to add a truss cant and we're going to put it right here
next to the chair. Let's draw another rectangle, just a small one, guys. And let's like this rectangle, and we're going to use PospleTol and let's create a circle. Just a small circle. And let's like this circle, and we are going to use Post Potal and we're going
to push this inward. Okay, so now you will be able
to throw your trash here. Next, we are going to
create a window right here. So let's like a rectangle. And let's like this rectangle, and we're going to
push this inward. So if you want to buy the ticket for the bus, you can wait here, and someone inside this box will help you to do
the transactions, right, and get the
ticket for the bus. Next, we are going to
create another rectangle, a big rectangle, guys. This is where the
bus should stop. And let's create a fence. Let's draw a smaller rectangle. And let's select this rectangle, and we're going to use put, and we're going to pull
this up a little bit. Okay, so the bus will
stop right here. Okay, guys, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
10. Designing Bedroom Interior with SketchUp: Hello guys. Welcome
back to the course. In this video, we are going
to start the third project. We are going to design a
minimals bedroom using SketsU. Inside the bedroom,
we are going to have a bed, a small chair, a small table, a wardrobe, and also a sofa. Okay, now let's get started. Firstly, we are going to
define the area for the bed. So let's grab your pencil and
let's draw a straight line. Okay, so here is the
area for the bed. And let's select the rectangle and we are going
to create the bed. Make sure the size is not too
big but also not too small. Okay, now we are going to
use the push pull tool. So let's pull this
up a little bit. Okay, so here is the bed, guys. Next, we are going to add
two pillows to this bed. Let's select rectangle. And let's draw two
rectangles right here. And we are going to
use post portal. We are going to do the same
thing for the second plow. Okay, next, we are going to
make this bed more beautiful. So let's like rectangle, and we're going to create
another rectangle right here. And let's use Pos Poll tool. Okay, here we go. Next, I'm going to add a
very small table right here. So you will be able to put your phone or laptop
near your bed. Okay, we're going to get
started with a circle. So let's circle. I'm going to put it right here. And let's use push pull
tool. Let's click this. And let's pull this up
a little bit. Okay. Here is the small table. Next, I'm going to add a sofa. I'm going to place
the sofa right here in front of the bed. So once you wake up, you
will be able to sit in the sofa and enjoy a cup of tea or maybe a
cup of coffee, right? Okay, now let's click
this and let's use push pull tool and let's
pull this up a little bit. Okay, we have a small
sofa in front of the bed. Well, actually, I'm going to make this bed more beautiful, so I'm going to make this
a little bit taller. So let's select push pull two, and we're going to pull
this up a little bit. Okay, so now it is a
little bit taller, as you guys can see right here. Okay, next, we are going
to create a wardrobe. So you can keep your
clothes there, right? So let's select rectangle. And let's use push pull two. And let's pull this
up a little bit. And let's, like,
rectangle again. And I'm going to draw a
big rectangle right here. And now we are going to
select this rectangle and let's use puss pull two and we're going to push this inward. Okay, so it looks like a closet, right, or a wardrobe. So you can keep
your clothes here. Next, we are going to
create a small table. So we're going to start
with a rectangle again. And let's use push pull tool. Let's draw another
rectangle right here. Let's like this rectangle
and we are going to use pus poll tool and
we are going to do the exact same thing like
what we did to this wardrobe. We're going to push inward. Okay, next, we are going
to add one more item. We're going to add a
chair for this table. So if you want to
use this table, if you want to study
in this table, you can sit on the chair. Okay, let's select a circle. And let's draw a circle, guys. Just a small circle, right? Well, actually, this is too big, so I'm going to make it
a little bit smaller. So let's use scale tool, and we're going to
make it smaller. Let's use post two and we're
going to pull this up. Here is the chair. I'm going to make the shape more unique. Let's add a rectangle
right here. Let's like that rectangle and we're going to use pus tool. The chair is going
to look like this. Okay, now we're going to move this chair closer to the table. So let's use Move tool. Okay, I'm going to put
it near the table. Okay, guys, here is the
design for the bedroom. A very minimalistic
bedroom, guys. We have a wardrobe. We have a small
table, a small chair, a sofa, a bed, and also a small
table near the bed. Okay, I think that's it.
That's all you need to know. I'll see you guys in
the next video. Bye.
11. Designing Bunk Bed with SketchUp: Hello, guys. Welcome
back to the course. In this video, we
are going to design a bunk bed that can
accommodate three people. So three people can
sleep in this bunk bed, and we are going to create a stairs so people can climb up. And the stair is going
to be multifunctional, so you can also keep your
stuff in the stairs. Okay, let's get started. Let's create a rectangle, a big rectangle right here, let's like the rectangle, and we're going to use
postpllTol let's pull this up. Okay, now we have a beam, right? And let's like a
rectangle again. Okay, next, let's draw
a rectangle right here. Next, you will need to copy
and paste this two more times and put it in the middle and also put it on the top. As you guys can see, I have already added two
more rectangles. So in total, we have
three rectangles, one, two, and three. Okay, next, we are going to use pusbleTol to
push this inward. So let's like the
first rectangle, and let's push this inward, and we are going to do the same thing for
the second rectangle. Let's push this inward. And we are also going to do the same thing for
the third rectangle. So let's use postbleTol
to push this inward. And we are also going to
remove the top here we go. Let's like razor and we're
going to remove the top guys. Okay, so it's going
to look like this. This is a bunk bed that can
accommodate three people. So the first person
slip on the top. The second person slips
in the middle and the third person
slips on the bottom. Okay? Next, we are going to add stairs right here so the first person can
climb up safely. Let's like a rectangle, and we're going to
create multiple stairs. I'm trying to make
the size the same, guys, just to be consistent. Let's like the first
rectangle and we're going to use possible tool
to push this inward, and we are going to do the same thing for
the second rectangle. We are going to
do the same thing for the third rectangle, push it inward, and let's do the same thing
for the fourth rectangle. Let's push this inward. And finally, we are going to do the same thing for
the fifth rectangle. Let's push this inward. And if you notice the stairs
is actually multifunctional. So you can use this as a stairs. You can climb up. You can also keep
your stuff here. Maybe you can keep your pencil, your book or any
other stuff, right? So it is multifunctional, guys. Okay, so here is the
bunk bed design. Well, I hope you
like it. This is actually far from perfect, and I'm not a
professional designer, to be honest with you. Okay, guys, I think that's it. That's all you need to know. I'll see you guys in
the next video. Bye.
12. Designing Kitchen Interior with SketchUp: Hello, guys. Welcome
back to decors. In this video, we
are going to design a modern kitchen using SketsU. In the kitchen, we are
going to have a sink, a place for stove, a refrigerator, and
also a microwave. Okay, let's get started. Let's create a rectangle. And let's select that rectangle. And let's use Puss pull tool, and let's pull this
up a little bit. Next, we are going
to create a sink. So let's a rectangle, and let's draw a small
rectangle right here. And let's select that
small rectangle, and let's use push pull tool. And let's push this inward. Okay, so here is the sink. We're going to make the
sink more realistic. So let's create another
rectangle right here. And let's, like,
small rectangle. And let's use post bootal and let's pull
this up a little bit. Okay, so here is the sink, guys. Next, we are going to create
a place for the stove. So let's create
another rectangle. I'm going to put it right here. And let's select that rectangle. And let's use post potol and we're going to push
this down a little bit. Okay, it's going to
look like this, guys. So you can place your
stove right here. Next, we are going to
add a cutting board. So let's create a
circle right here. Well, actually, this is too big, so I'm going to make this
a little bit smaller. And let's like this circle. And let's use Pop tool. And I'm going to pull
this up a little bit. So this is like a cutting board. You can prepare your
food right here. Okay, next. We are going
to add a refrigerator. So let's create another
rectangle right here next to the kitchen. Let's select this rectangle
and let's Pop two. Now we have a refrigerator. Very cool. This refrigerator
will have two sections. The first section is the freezer where you keep your ice
cream or your meat, and the second section is the normal fridge
where you can keep your fruits or vegetables
there or your leftover food. Let's create a rectangle. This is the freezer and the second one is
the normal fridge. Let's like the first rectangle. And let's push this
inward a little bit. So it looks a little
bit different compared to the regular fridge. Okay, now we are going to make this kitchen more beautiful. So let's add another rectangle. And let's add another
rectangle on the top. Just a small rectangle, guys. And let's use push pull too. Okay, so it's going to look
like this. Very cool, right? Actually, there is one more
thing that we're going to do. We're going to add a microwave. So if you want to hit your food, you can do it too
in this kitchen. So let'se rectangle. And let's create a
rectangle right here, guys. So we're going to assume
this is the microwave. And let's like this rectangle, and let's use Postbt and
let's push this inward. Okay, so here is the microwave, guys. Okay, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
13. Designing Home Office with SketchUp: Hello, guys. Welcome
back to the course. In this video, we are going to design a home office
or a study room. We're going to have
a small chair, a desk, a cupboard, and also a small window. Okay, let's get started. Let's create a rectangle. And let's select that rectangle, and we're going to use
Puss Pull tool and let's pull this up a little bit. And let's draw a
rectangle right here. Let's like this rectangle, and we're going to
push this inward. Next, we are going
to create a chair. So let's circle. Make sure the size
is not too small, but also not too big. And let's like the circle, and let's use pus pot. Okay, so here is
the chair, guys. Next, we are going to create a cupboard next to this table. So let's like a rectangle and let's draw a rectangle
next to the test. Let's select this rectangle, and we're going to use PopolTol and we are going to make this cupboard
look more like a bookshelf. So let's throw two rectangles, one on the left, and the
other one on the right. And let's draw another
rectangle on the bottom. Okay, let's like the
first rectangle. And let's use push pull tool, and we're going to
push this inward. And we are going to do the same thing for
the second rectangle. Let's push this inward. And we are also going
to do the same thing for the third rectangle,
the one on the bottom. Let's use Post boo tool
and push this inward. Okay, so this is
like a cupboard. You can keep your stuff here. Maybe you can keep your book
or any other stuff, guys. Next, we are going to add additional wall and
also a TV or a monitor. Okay, let's create
another rectangle. I'm going to put it right here. Let's add another wall, and let's add one more wall. And we are going to
add a small window, and the shape is
going to be a circle. So let's like a circle. Okay, now, let's add a small window on the wall so
you can see who is coming. Let's like this circle, and we're going
to use pospoolTol and let's push this inward. Okay, so here is
the window, guys. Next, I'm going to add, like, a small sofa. So let's, like rectangle. I'm going to put the
sofa right here. It's going to be a
small sofa, guys, and let's use PospTol and let's pull this up a little bit. Okay, so here is the sofa. Actually, there is one more
thing that we need to do. We need to add a TV or
a monitor to the wall. So let's like a rectangle, and let's create
a big rectangle. And let's put it right here. And let's like this rectangle, and we're going to use
PospllTol and we're going to push this a
little bit inward. So it's going to
look more realistic. Okay, so here is
the TV. Very cool. Okay, I think that's it, guys. That's all you need
to know. I'll see you guys in the next video. Boy.
14. Designing Bathroom Interior with SketchUp: Hello, guys. Welcome
back to decor. In this video, we
are going to design a modern bathroom
interior using SketsU. Okay, let's get started. Firstly, we are going
to create a toilet. Let's create a circle. Make sure the size is not too
big but also not too small. Let's select this circle
and we are going to utilize PospTol and we're going to pull this
up a little bit. Next, we are going to create
a hole in the middle. Let's create another circle. Make sure the size is smaller. But not this small. Let
me try again, guys. Let's select the circle, and we're going to use
Puss Pul to again. And we're going to
push this inward. Okay, here is the toilet, guys. Okay, we're going to make
the shape more realistic. So let's like a rectangle, and we're going to create
a rectangle right here. And let's like this. And we're going to use
push pull tool guys. And let's pull this
up a little bit. Okay, now the shape is
more realistic, guys. Next, we are going to create
a place for you to take. So let's like a rectangle. And let's use Post Buto. Okay, we're going to take
your inside this box. Let's create another rectangle. And we are going
to use Post Boto, and we're going to
push this inward. Okay, so you can take your
inside this box, guys. Next, we are going
to create a beta. So let's select a circle. And it is very important
for you to make sure the size is proportional
to this box, so it looks realistic. Okay, here we go. And let's like this circle, and let's use Pus Bolt, and we're going to pull
this up a little bit. Okay, here we go. Next, we are going to
create another circle. We're going to
create a hole, guys. And make sure the
size is smaller. And let's create the hole.
Let's like the circle. And let's push this inward. Okay, here is the battub guys. Well, actually,
I'm going to push this a little bit further. Okay, here we go. Okay,
now we have a toilet, we have a bathtub, and we also have a box where
you can text your, right? Now we're going to
create the sink. So you can wash your hand and you can also
brush your teeth, and we're also going to
add mirror to that sink. Okay, let's create a
rectangle next to the battub. Let's like this rectangle, and we are going to
use Post Pul tool, and we're going to pull
this up a little bit. Next, we are going
to create the inc. So let's create a
circle right here. And we are going to move
the circle using move tool. We're going to put
it right here, guys. Next, we are going
to create a hole. So let's use post pull tool
and let's push this inward. Okay, now we have a sink, and let's add the mirror. So let's like a rectangle. Okay, let's add the
rectangle right here. Make sure the size is not too
big but also not too small. Next, we are going to
create the mirror. So let's throw
another rectangle. And let's select this rectangle, and we're going to
use Puss Ball tool. We're going to pull this
a little bit, right? So it looks like a
mirror. Okay, very cool. Now we have a shower box, a toilet, a bathtub, a sink, and also a mirror. Okay, next, we are going to
do two more things, guys. We're going to add the wall, and we are also going to create a small swimming pool so
you can also swim there. Okay, very cool,
right? Let's grab your pencil and let's
create the wall. Let's draw a straight line Okay, now we have a wall, and
let's select a rectangle. And let's create
the floor, guys. And let's draw
another rectangle. A smaller rectangle, guys. So this is going to be
the small swimming pool. And let's like the
second rectangle, and we're going to
use Pos pool too, and we're going to push
this down a little bit. Okay, now you have a swimming
pool. Very cool, right? Okay, I think that's it.
That's all you need to know. I'll see you guys in
the next video. Boy,
15. Designing Chair & Sofa with SketchUp: Hello, guys. Welcome
back to the course. In this video, we are going to design a furniture using SketsU. Specifically, we're going to design a chair and also a sofa. Okay, now let's get
started with the chair. Firstly, we're going
to create a rectangle. And let's use Post Bull tool, and we're going to pull
this up a little bit. And let's draw another
rectangle right here. Make sure it is a
small rectangle. And let's pospll two, and we're going to pull this up. A little bit. And let's draw
another rectangle, guys. Okay, now let's select this rectangle and
we are going to use Possible tool and we're going
to push this inward, okay? Okay, now we have a chair. You can sit in this chair, guys. Next, we are going to design the second furniture,
which is a sofa. Okay, we need to
have more space for the sofa because we're going
to create a big sofa guys. Let's get started
with a rectangle. And let's like this rectangle, and we're going to pull
this up a little bit, guys. And let's draw another
rectangle right here. And let's like the
second rectangle, and we are going to use push pull tool again and
we're going to pull this up. Okay, now it looks more
like a sofa, right? And when you are
relaxing in the sofa, you might want to
rest your arm, right? So we're going to create a place where you
can rest your arm. Let's like a rectangle. Okay, here we go. And
we are going to do the same thing for the left arm. This is for the right arm. This is for the left arm, right? So let's, like, rectangle again, and we're going to do
the exact same thing, guys. Okay, here we go. And let's use push pull tool, and we're going to pull
this up a little bit. And we are going to do the
same thing for the second one. Let's use Pus pot and we're going to pull
this up a little bit, make sure the
height is the same. Okay, very cool. And next, we are going to make this sofa more beautiful
and also more functional. Sometimes you are very tired and you want
to sleep, right? But you don't want to
go to your bedroom. You just want to
sleep in the sofa. So we're going to
modify the sofa a little bit so it can
accommodate that need. So let's draw another rectangle. Here we go. And let's
like this rectangle. And we're going to use
PoS Ball tool again. Okay, now you can sleep in
the sofa. Look at this. You can pull this and you can sleep here,
right? Very cool. Very cool sofa, guys. Okay, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
16. Designing Dining Table with SketchUp: Hello, guys. Welcome
back to the course. In this video, we are going
to design another furniture. Specifically, we're going
to design a dining table. Okay, now, let's get started. Let's create a rectangle. Make sure the size is not too
big but also not too small. And let's use push pull tool, and we're going to pull
this up a little bit. And let's draw
another rectangle. Let's select this rectangle, and we are going to
push this inward. Next, we are going
to create the chair. Let's create a circle. You can use any shape
that you want, guys. It is totally up to
you, but in this case, I'm going to use a circle. Let's use Puss Ball tool, and let's pull it
up a little bit. And let's create
another rectangle. Just a small rectangle, guys, and we are going to move the
rectangle to the cylinder. And let's use Moth tool and we're going to
put it right here. And let's use Pus
Ball tool again. Okay, now we have a chair. So you can sit in
this chair while having your lunch or
your dinner guys. Well, if you want to make
this a little bit taller, you can use pus boll tool again and just adjust
the size, right? Okay, now we are done
with this table, we are going to
create another table. Well, we need to
have more space. Okay, let's create a
rectangle right here. Make sure the size
is not too small, but also not too big. And let's use Post Ball
tool. Okay, here we go. And let's create
another rectangle. And let's grab your pencil. Okay, this is the
second table, guys. Now let's add another chair. Let's create a
rectangle here, guys. And we are going to
utilize Pus Bull tool. So let's pull this
up a little bit. And let's create another
rectangle right here. Just a small rectangle, guys. And let's select this rectangle, and we're going to use Pus BT and pull this up a little bit. Okay, now we have a chair
so you can sit here while enjoying your food. Next, we are going to create
a rectangle right here. And we're going to
select this rectangle, and we're going to use Plus poll tool to push this inward. Okay, so you can keep
your stuff here. You can keep your sponge, your knife, your fork, or maybe any other sauce, like soya sauce, tomato sauce, chili sauce, or whatever. You can put them here, guys. Okay, very cool. I think that's it. That's
all you need to know. I'll see you guys in
the next video. Bye.
17. Designing Car Garage with SketchUp: Holly guys, welcome
back to the course. In this video, we are going
to decide a car garage. Okay, let's get started. Firstly, we are going
to create a rectangle. And we are going
to use Puss Pot. And let's pull it up. Next, we are going to
create another rectangle. And let's use Puss PT, and we are going to push this inward so the car
can get inside. Okay, here we go. Next, we are going to create an additional fence
for the garage. Let's create another rectangle. And we are going to use push pull tool again and we
are going to pull this up. Okay, here we go. As you guys can see, we
have fans on the left side. Now we are going to
create another fence, and we're going to put
it on the right side. Okay, let me adjust
the positions. And let's create the fence. Okay, here we go. And we are going to
use pospoTol again. And let's pull this up. Okay, here we go. Next, we are going to add
additional roof. So when it is rainy or snowy, you are not getting wet. So let's create a rectangle. And let's click on
that rectangle. And we are going to use
the post pole tool. Okay, here is the
roof. Okay, very cool. Okay, so your garage
looks like this. Very cool, right? Okay,
guys, I think that's it. That's all you need
to know. I'll see you guys in the next video. Bye.
18. Designing Modern Cupboard with SketchUp: Hello, guys. Welcome
back to the course. In this video, we are going
to design a modern cupboard. Okay, let's get started. Firstly, we are going
to create a rectangle. And let's create
another rectangle. Okay, now we have two rectangles and we are going to
use possible two, and we're going to pull this up, and we are going to do the same thing to the
second rectangle. So let's click this and
let's use possible two, and let's pull this up. Okay, now we have two beams. Next, we are going to create another rectangle right here. And we are going to use push
B tool to push this inward. And let's push this inward. Next, we are going to create another
rectangle right here. And we are going to
do the same thing. We're going to use Pus bull
tool and push this inward. Okay, here we go. And let
me adjust the positions. Next, we are going to create a very small circle And we're going to use
Push Pull to again. So let's click this, and
we're going to pull this. So you can hang your
clothes here, guys. You can put your hanger here. I know this is too big. Maybe you can make it smaller, so it will look more realistic. Next, we are going to
add multiple drawers. Let's create multiple rectangle. I'm going to copy and
paste this multiple times to make sure the size
is exactly the same. As you guys can see, now we have six rectangles and their
size are exactly the same. Let's click on one of
these rectangles and we're going to use PSP
tool to push this inward. And we're going to
do the same thing to the second rectangle. Let's click this
and we are going to use PSP tool and we're
going to push this inward. And let's click on
the third rectangle, and we're going to use Pus Bt, and we're going to
push this outward. So this is like a drawer
where you can pull this. And we are going to do the same thing to the
fourth rectangle. So we're going to use
Pus Boto and we're going to pull this outward. Okay, here we go. Next, we are going to click
on the top of the beam, and we're going to press delete. So it looks like this. It looks like a more
realistic drawer, right? Next, we are going to click
on the fifth rectangle, and we are going to push this inward
using Post Ball tool. So we're going to make this the same like the first and
the second rectangle. And we're going to do the same thing to
the sixth rectangle. We're going to use Pus Boto, and we're going to
push this inward. Next, we are going
to create a chair. So let's click on circle and we're going to create a small
chair right here. And let's click this and
we're going to use Pus Boto, and we're going to pull this up. Next, we are going to create a sliding door for
this cupboard, and actually it is very easy. You just need to create a
small rectangle right here. And let's click on
this rectangle, and we're going to
use Pos Ball two, so you can pull
this to the left. Okay, it looks great, right? Okay, I think that's it.
That's all you need to know. I'll see you guys in
the next video. Bye.
19. Displaying 3D Design in Virtual Reality : Hello, guys. Welcome
back to the course. In this video, we
are going to view our SketU design in virtual
reality environment. Okay, now, let's get started. Firstly, just open
your file and you will need to download the
file in SKP format. So let's click Download
and let's select SKP. Okay, we have successfully
downloaded the SKP file. Let's go back to Google Chrome. You have two options.
You can use Simlab. You can also use ShapSPark. If you want to use
Simlab you will need to download Simlab. But if you want to view
your design in browser, you can use ShipSPRk. You don't need to
download anything, you don't need to
install anything. Let's click Log Int. And I'm going to log in
using my Gmail account. If you haven't
created your account, make sure that you create
your account first. As you guys can see, I have
successfully logged Int, and here is my dashboard. Okay, let me show
you an example. Let's click for It will
take few seconds to load, maybe five or 10 seconds. So just the way it goes. Hopefully, it doesn't
take too long. So the virtual reality
is going to look like this. This is not mind. This is just an
example provided by Shep Spark. Very cool, right? Okay, now we are going
to view or design in Sheppark virtual
reality environment. Actually, the process is
very straightforward. You just need to upload
the Tree D design. You need to make sure
the file format is FBX, GLTF, DOE, or OBJ. But if you remember, when we downloaded the T D
design from SketUp, the file format was SKP. So we need to convert SKP to OBJ first before uploading
the design to Shap Spark. Okay, let's do it. We are
going to use this website called Image two SDL. And you need to make sure
that you select SKP and also OBJ. Okay, let's do it. Let's click Upload SKP file. And we're going to upload
this office building dot SKP. Let's click Open, and let's
click Convert to OBG. Okay, it will take
a few seconds, maybe ten or 15 seconds. Okay, here we go. So here is the three D model,
the office building. And let's download it.
Let's click Download. Okay, we have successfully
downloaded the OBJ file. Let's double click
on the Zip file. It is inside this folder. Let's go back to
Google Chrome and let's go to Chip Sport and let's click Import your SNT
let's click Browse file. Let's open this folder
and make sure that you select the OBJ file
and let's click Open. Next, you will need
to name the scene. I'm going to name
it office building. You can name it
whenever you want. It is totally up to you. For the input scale, I'm going to select one metter
and for the input up axis, I'm going to select Y. And let's click Import. Okay, now it is
uploading the file. Well, the process
didn't take too long. It only took 5 minutes for Cp
Spark to load the TD model. Let's click FEW Let's
click on the Tree D icon. It will take few
seconds to load. Here we go. Here is
the sketsU design. It doesn't look that
good because we have an added color
to the design. So this is the entrance door. This is like the windows. You can rotate around. Okay, next, we are going
to do another thing. We are going to design coffee shop interior
using Copernik AI, and the process is going
to be very simple. We are not going to
design manually. We're going to write
a simple text prom, and this AI tool is going to generate the
design automatically. So firstly, just go to this
website, copernik.com. And next, you will
need to write a prom, make sure your prom is
clear and specific. Okay, let's write
the prom, guys. Interior design for coffee shop. But with modernt and aesthetic design. Okay, that's my prom,
a very simple prom, and let's click January. Okay, it will take
approximately a minute. Just wait, guys, and I'm so
excited to see the design. Well, it didn't take
too long, guys. It only took 30 seconds or
even less than 30 seconds. Okay, here is the design. We have tables, chairs, a small kitchen, and also
a door. Look at this. Very cool design. If you want to download this
design, just click Download. Okay, I think that's it.
That's all you need to know. I'll see you guys in the next
Chris Raharja, Data Scientist & AI Enthusiasts
