Transcripts
1. Introduction: Hi, I'm booby from
axilla and cluster it. I'm a violin jewelry maker, likely to this
jewelry making class. I have been making jewelry
for a long time now. I love experimenting, trying new designs and
developing new patents. On my Etsy shop,
actually handcrafted, but I offer lots of detail tutorials for different designs and
different techniques. Those can be a part of your
creative journey venue. Wrapping up is a very versatile
technique of gelatin making. It requires very few tools and with a few techniques
which you have learned, you can create
beautiful jewelry. This course we'll be creating this beautiful kosher
design pendant. Just need some basic supplies
as listed in the course. We've alone to create the frame and set
the stone within it. And using all the techniques
we have learned so far, we will create the entire
kosher design pendant. If you're new to my pink. And just beginning, then do take the by wrapping
for beginners course. Dependent using
single via technique. I pose before attempting
does reject design. It is a simple yet
beautiful design and it is really flexible. You can change the
shape and size of the stone as per
your availability. I'm sure you will have fun and enjoy creating this
design with me. If you're ready, then
let's start right at me.
2. Tools & Materials Used in this Class: Let us now look at the materials and tools used in this class. We will be using 44
inches of 20 gauge around wire and 122 inches
of 30 gauge round wire. We will need an
oval cabochon stone, 20mm X 30mm is the size that
I'm using here. We will need a few
beads of your choice. Any beads will do, I'm using two beads of 2 MM, three beads of 2.5 MM
and two beats of 3 MM In this project. For the tools we will need Chain nose pliers
or flat nose pliers. Now nose pliers, flush cutters, and a 5M doorbell or
bail making pliers. This is all we need. If you're ready,
then let us start.
3. Kosha 1 - Preparing Wires for the Frame: This class we have working
with the kosher design. This design is perfect
for oil size tone. Here. This is the one I have created using a
laboratory that stone. But for this class we are using a slightly smaller
black onyx garbage on. So you can definitely use any
size oval stone you have. We are going to use it
horizontally and have a flat back. The stone that I'm using is approximately 25 MM by 1920 MM. And it has around
forum and tech. We're taking 20 gauge
around via four pieces. Well inches long. We will start by marking
the centers at six inches. So our first step
is to wrap around all the wires and get them
ready for making the frame. For this, we are using
24 inch long weaving while we will be
doing two-by-two, we've over four values here. This is the one. These wires
will create our frame. First, we will find the
center of all of even via. We will place the
center on Bio one. We're going to call
this wire as y of one. We will wrap over via one for two to three rotations to secure the weaving
by R2 means wire. The wire two on the top and
drop twice around both wires. On the right side. We have to view overall on
both sides of the center. So right now we are
leaving on the right side, bringing the virus
up from the center of y of one and via two. We will learn the next while. This is via three rapport via
two and via 342 rotations. And bring the wire up from
the center of wire to entry. The last via, via four, wrap over via 34
for two rotations. This time we will bring
the virus up from the center of via
one and via two. Now we're going back to, we want to more
rotations on via 23. This kind of weaving will
give us triangular design. The stem device at the
bottom of y of one, the rap for two
rotations on via van. And then to end our forest weaving rotation, rapport via one
for two rotations. Here it is. This is our
van rotation of weaving. Add one more rotation
on this side. We are repeating the same steps. We want to rotations
on two wires, giving us a triangular design. You can be with your left or your right hand as convenient. All throughout makes
sure that the bees virus remains straight
and do not deform. We can slightly spread apart the base virus to create
more space in-between. Now that the second
rotation is done, we are going to be photo few
rotations on the right side. On my other one, we are ending
our weaving on the side. We've got the extra
weaving via and at this point and secure the
wire and using pliers. Now we will continue to
live on the left side. That will slightly
spread out dividers. And I will show you how you can leave with your left hand. The technique remains the same. We are just weaving
with the other hand. If you are leaving
material right hand, then just rotate the
virus and continue to V1. The same method. Make sure that all the
views are uniform and keep on pressing the weaves together
to get nice glows views. Now we are ending the
weaving on the side to fulfill rotations on via one. Cotton security
extra weaving Maya. As you can see, our basic
frame bios on already.
4. Kosha 2 - Creating Frame for the Pendant: Now that our frame bias
already and this part we are going to be shaping our frame and we will
work on the bill. We want to wire a
one at the bottom. And the weaving French
side should faces, please the stone horizontally. We are going to be using stone as our support for
shaping the virus. The virus, as shown and gently core of
the virus we're using fingers only makes sure that the fingers and the center
of the stone width. We are going to be carving
the virus around the stone. Like this. This cone formula with one hand and glove the virus
with another hand. We want a nice teardrop
shape around the stone. Also make sure that y of
four that is the top file, slightly goes over
the surface of the stone because that is mostly going to hold
the stone from the top. Now here you can see that the wires are
intersecting each other. So we are going to mark
that point on both sides. We will remove the stone. Now using pliers,
we are going to fold over virus up from
this marked point. We want all far for virus to remain parallel at all times. They should not overlap
and you can see they are now perpendicular
to the base. Repeat the process
for the other side. All four wires are parallel. They are not overlapping
each other and we are going to be folding them up. In all. We have eight wires at
this point over here, four wires on each side and both sides wire
should be parallel. Hold them like this
formally, but gently. You can see that there are
four wires aligned properly, perpendicular and the center of the weaving at the bottom. This is our basic frame. Now that our basic
frame shape is ready, we will now vote on the
bill for the pendant.
5. Kosha 3 - Making Bail for the Pendant: Now that our basic
frame shape is ready, we will now walk on the
bill for dependent. We will first do the weeping and then they will
shape the bill. We're using a 36 inch
long weaving Vieux. We will start near
one of the virus. The virus formally
as we saw earlier. Then we will wrap over all eight wires
photo few rotations, weaving with the
shorter end right now. This is just to hold
all the wires together. Then we will end this violent
or weaving on this side, we are going through
the center of bio 12 and then we're weaving over
via one for few rotations. This well secured
the side violent. Got the extra leaving layer. Make sure the via the end towards the
inner side of the frame. So at this point,
all over eight wires are connected together. And then we are
going to separate. So both wire for
that is the topmost, while that's what we are going
to be making a bail width, we will slightly pull them up. Now, we will take the
last wire that is y of one on the left side and
all the other virus, they go towards the right side. We now have five wires
on the right side. One wire to the left, that is y of one. We have five wires
on the right side and the two wire Ford
are at the front. And we have slightly
pull them towards us. We are going to
spread them apart a little to create this kind
of a space in-between. We are now going to be
doing figure-eight. We've over these two virus. It does one rotation on second rotation go
through the center, go over to the other
via rapid opposite. While for two rotations. On second rotation come
back to the left side. While on the left side we
will wrap for one rotation. Grep for the second rotation. And second rotation
we go across to the opposite right
side via rotation. Rapport, another rotation, come up from the gap in-between, pick the virus over
to the left side. I hope you can see
it much better here. On every second rotation
we are going over to the opposite side
vial from the center. This is figured it
we've over two wires. The length of the bill
can be up to you. But right now, I'm
going to be doing 12 complete rotations
of the leaf. Here you can see at
this point we are going to straighten both
these wires using pliers. Now both wires are parallel with an equal distance or similar
distance in-between. So for me right now this distance between
two wires as five MM, if you want a broader build
and increase this distance. So again, we are
going to be weaving for 12 rotations over
the parallel virus. Once you are done, we will
again use the pliers to fold both sides virus in towards
the center. Like this. As you can see, the virus
are intersecting each other. This point. We will fold the virus up from
the intersection point. You can mark this point and
then for the violet up, now you can see this gap. We still have to V4. So we have to leave till we
reach this point will be approximately ten to 12
rotations of weaving. Again, make sure that the
views are close to each other. So keep pressing the
views together every few rotations to end up leaving. We will leave over one of the
virus for a few rotations, cortex Dre and secure dividing. Basic frame along with the weaving for the
bail is now ready. The next part we are going
to be setting the stone.
6. Kosha 4 - Setting the Stone: Now that our frame is ready, we are going to be setting
the stone at this point. Insert the stone
from the backside. So in case it is
elaborated, Moonstone, make sure that the flash is at the right angle, it around. And now, using the
pliers and fingers, I'm going to create a dent in the back while that is y of one. These dense will create the supports for
the stone to sit. And at this time remain
extremely cautious because the suppliers should
not damage the stone. Also, you can see that
we do not want the remaining of y of one
to change its position. We can slightly press our fingers to make
sure that via Ford is going over the stone and it is holding
the stone from top. This has set our stone not move or fall
from its position. Now we are going
to shape our bail and we will wrap the
virus to the front. To do that, we have
this bill within here, please, or five MM Dowell at the back in the center
of the weaving. You can use some
dealmaking pliers. The virus over the doorbell. Now I'm using pliers. We are going to be creating this dent at the
bottom of the weaving. We are slightly going
to fold the wired up. You can now see that these wires are
perpendicular to the front. Now call device gently and
bring them to the front, pass them through this
gap about the stone, and push them to bring them
to the front of dependent. Straighten the virus using fingers and close
the bill properly, press it at the bottom. We now have two wires at the front and our
bail is fully formed. This is how it looks
at this point. We're now going to be shaping
these two wires as such, like in a similar. So make sure that first of all they should remain parallel. We are going to be
carving the virus. Use your thumbs. Pressed the virus with your thumb so that
they remain parallel. Dig them down from the outer edge of the
dependent of the frame. We will cut extra Bahrain. And we are going to be
wrapping these violence over y of one from which we have
created these dense. So there is slight
gap between 12. That's where we want
to fold over virus. Take your time and
make sure that the pliers do not damage
the stone because certain stones are
quite soft and they do get scratches
because of pliers. Our bail is now done and we have wrapped the
wire ends properly. The next part creating this weaving component
that we have here.
7. Kosha 5 - Let's now Weave: We're now going to be creating this weaving component
that we have here. We will be doing three
by two V over two wires. For this, we are
going to be choosing the nearest wires to the front. Select any two parallel wires which are closest
to the front side. We are going to be weaving
over these two wires using 24 inch long weaving
via first wire, we are going to be doing
3D rotations of weaving. Cortex job I had
ended the beginning. And secure though. We are going to slide this down. Now. We will do two
rotations over both files. This is our one
rotation of weaving. It is three rotations on one vial and two rotations
over both wires. Keep pressing the virus together
to get nice glows reuse. At this point we are going to be doing 14 complete rotations, but do not get
extra viewing via, as we may add more
rotations if needed. At all times, make sure
that the virus remains flat and straight to of course, once you are done
with 14 rotations, we can stop right here. And now we will give it this curvature folder via down like so towards
the bottom of dependent makes sure that
the virus remain flat. And I'm using the thumb gives
shape to the curvature. You can follow
your own intuition for the curvature shape. I had to add 23 more
rotations of weaving. And I'm still adjusting this curvature for the virus down. I'm going to be cutting off
extra weaving bio here. Folding the virus down. I'm going to be still
adjusting this. Take it more towards stiff
left side frame bio. We will cut extra wire ends and similar to what we did before, we are going to be wrapping
this overview of one, pass the gap between buyer 12
and tightened the violence. We are almost done. Just a few more things remaining and up and
it will be tidy. Next part we are going
to be working with this coil via right
here and the medial. And the last center wire from which we are
creating a loop.
8. Kosha 6 - Adding the Beads: This part we are going
to be working with this coiled wire
right here and the medial via the last center wire from which we are
creating a loop. We'll start with
the coiled while. For that we are taking
our next wire that is closest to the
three by two V Virus. Using a piece of 18
inch long bearing bio, we want to coil over this wire. The wire is around
while we will be able to slide our coil
down once it is viewed. Slide the coil down
to the bottom. Now we are going to be
coating this wire to follow the curvature
of three by two VIF. Again here also I have to
add a little bit of coiling. Weaving has to reach till
the outer edge of dependent. Just add a few rotations. This looks good. So we are now going to cut
the extra weaving wire, the base via down
and to the back. We will guide the
extra bass viol and wrap the wire and
similarly over y of one. Keep on adjusting until
you are satisfied. Pick the next file. Now we are going to be adding
some beads to this wire. I'm going to be using
some copper beats here. I'm using three different sizes. It is two mm, 2.5 MM, YY MM. I'm starting with the
smallest 13 beats of the smallest size, two to three beats
of the medium-size depending on the size
that you are using. And two beats of
the largest sites. We want a gradual increase
in the size of the beat. Now we are going to be folding
the wire down and then we will follow the
inner side goal of the three by two views. Like so. Now at this point, fold the wire down. Now at this point
we are not going to be cutting extra via, We will just create this dentate right
side frame bias to secure the wire position. We're not cutting the extra bile will bring the virus to
the outer left side. Just at the bottom of the bill. This is where we want the
viral adjusted position. So this is done right now. Now we will use the last
wire on the right side. We will bring the wire down. Now we want to create a loop. And this small
curvature we have left. This kind of a loop. We are going to be
calling the vile. Use your thumb to make
it the exact size. Go the vial and
counterclockwise direction for one complete rotation to create a nice loop in that portion. Bring the Via back to the outdoor right side
folded down and to the back. I hope you can see the
loop that we created. We will cut the extra via
here and wrap divided. And similarly. Now with this, our right set of dependent
is done but will now walk on the left side two wires
and finish our pendant. I hope you all are enjoying. Next part, we will now walk with this top
portion on the left.
9. Kosha 7 - Adding the final Details: Now that the right side is done, we will now walk with this
top portion on the left. We will use these two wires. So first we are
working with this wire which we have at the
bottom of the bill, the one on which
we added the bids. Now we are going to
be coiling over this while using a 12
inch long piece of weaving vile fire around one inch on little
less than one inch. Got both sides extra
weaving patterns and secure properly with pliers. Slide the coil down. Now called the coil
on the top and the reverse direction in the opposite direction
over the bail. Here. I'm also going
to be cutting off the other side leaving via end. Now we will even cut
the extra B's via, just live enough to
wrap over the bill. We will take it towards the
inner surface of the bill and rapid over tightened
with suppliers. Do make sure that
the violin does not come up from the top. The violence should not
come towards the top side. It is almost ready. Now just one last
five are remaining. We are going to be
carving divided up and follow the curve of
the coil bio, please. Just inside that file
of the wire down. We'll cut extra and
similarly wrapped dividing towards the inner
surface of the beam. How simple it was that as an
advisor, really nice design. I enjoyed creating
it every time and it is my go-to design
for milestones. Works perfectly with any size, any stone, any shape. Thank you for taking
this class with me.
10. Conclusion: Congratulations, you have
just completed the course. I hope you enjoyed creating
duality in with me. This was just the first step
towards learning to via, via wrapping is all about
manipulating the virus. It is important to learn
the basics properly, to give proper codes and
create proper shapes. This course teaches the basic via weaving and via wrapping techniques from which you can create limitless
jewelry designs, as per your imagination, practice will make
your skills more refined and you will need lots
of patients while working. Use your inner creativity to develop your skills and
create beautiful duality. I'll be posting lots of
new courses and where I've been for you to
enjoy and practice. Don't miss out my class on
creating the Aurora pendant. You can also visit my website to purchase advanced
level PDF tutorials. You can even follow
me on Instagram and Pinterest to have a look
at some of my other work. Thank you so much for
taking this course with me. Hope to see you soon in
some of my other courses. Till then, keep practicing.
Gopi Dave, Wire Wrapped Jewelry Maker
