Fast Easy PCB Design for Beginners using OrCAD, PSpice and Allegro | Kirsch Mackey | Skillshare

Fast Easy PCB Design for Beginners using OrCAD, PSpice and Allegro

Kirsch Mackey, Engineer, Developer and Entrepreneur

Fast Easy PCB Design for Beginners using OrCAD, PSpice and Allegro

Kirsch Mackey, Engineer, Developer and Entrepreneur

Play Speed
  • 0.5x
  • 1x (Normal)
  • 1.25x
  • 1.5x
  • 2x
9 Lessons (39m)
    • 1. Introduction to OrCAD

      2:34
    • 2. The PCB Design Process with OrCAD

      1:20
    • 3. OrCAD Trial vs OrCAD Lite

      2:20
    • 4. How to install OrCAD Lite

      2:26
    • 5. Creating and Simulating a schematic in Capture CIS Lite

      9:14
    • 6. Footprints and Setting PCB Parameters

      8:59
    • 7. Routing the PCB

      5:16
    • 8. Gerber and Drill

      7:05
    • 9. Recap

      2:27
  • --
  • Beginner level
  • Intermediate level
  • Advanced level
  • All levels
  • Beg/Int level
  • Int/Adv level

Community Generated

The level is determined by a majority opinion of students who have reviewed this class. The teacher's recommendation is shown until at least 5 student responses are collected.

145

Students

--

Projects

About This Class

Learn how to design a printed circuit board from scratch using the industry leading software, Cadence OrCAD Capture, PSpice and OrCAD PCB Editor.

Meet Your Teacher

Teacher Profile Image

Kirsch Mackey

Engineer, Developer and Entrepreneur

Teacher

I am a Ph.D. student in electrical engineering specializing in control system design for power electronics and power systems. From a very young age I knew I wanted to be an engineer, inventor, entrepreneur and educator. One of my greatest passions is teaching others the technical skills they need to get their projects done.

See full profile

Class Ratings

Expectations Met?
  • Exceeded!
    0%
  • Yes
    0%
  • Somewhat
    0%
  • Not really
    0%
Reviews Archive

In October 2018, we updated our review system to improve the way we collect feedback. Below are the reviews written before that update.

Your creative journey starts here.

  • Unlimited access to every class
  • Supportive online creative community
  • Learn offline with Skillshare’s app

Why Join Skillshare?

Take award-winning Skillshare Original Classes

Each class has short lessons, hands-on projects

Your membership supports Skillshare teachers

Learn From Anywhere

Take classes on the go with the Skillshare app. Stream or download to watch on the plane, the subway, or wherever you learn best.

phone

Transcripts

1. Introduction to OrCAD: Hello. Welcome to the or CAD Light PCB editor tutorial. I'm gonna show you how to use this free piece of software to make your first PCB and how to get used to the or CAD light environment to go through the electron ICS and electrical engineering design process. Okay, So or cat light is a light version or not as heavy lifting version off the more advanced software suite provided by Cadence. And that's the or cad sweet on the allegro. Sweet. Now, those software programs are very powerful tools, but they're also pretty expensive. So I'm gonna show you how to use the or cat light, sweet toe understand those more expensive pieces of software, but for free, this license does not have any limitations. There's no expiration date on it and it allows you taste of the best features and cadences . Best products or cat, PCB editor and or cat capture C. I s Also it's very similar to Allegro PCB editor and a leg Allegro design entry C I s right also to your designs are not stuck to an online platform like maybe other software packages are involved. Now, this is similar to key cat this software on other software programs like Mentor graphics and pads and whatnot. But the main difference between or cad and Cadence sweet is that it's an industry standard software package. So companies like Apple Computer, IBM, Intel on other major players in electron ICS design, manufacturing and consumer electronics. So they used the or CAD and cadence on allegro suite packages. Okay, so this is the industry standard software that you want to get used to. And also, it does have a high learning curve, which is why I made this video so you can get past that learning curve. But with this high learning curve and how powerful the software is, I promise you you'll be able to use any other PCB editor a PCB design software with ease. You be able to pick it out almost just like that once you learn this or cad Cadence suite software. All right, so in the next video, I'm going to just dive right in and show you how to make your first printed circuit board using capture C. I s light and or cat PCB editor Light 2. The PCB Design Process with OrCAD: in the PCB design process, we typically have a schematic, which is a drawing of the high level circuit diagram. Then where possible, we test the functionality of the circuit trying in simulation. A lot of time simulation is not available to you, so you just have to go based on theory and electrical engineering knowledge. But it's always nice to have simulation. The last phase is PCB layout. This has to do with the mechanical and physical aspects of your actual printed circuit board. So it's not just conceptual, it's mechanical. And all physical parts of the PCB or CAT has a software program for each of these phases of the design process. For a schematic capture we have capture, so that's very aptly named. It captures the circuit idea in to a circuit trying known as a schematic. Next, the handle simulation is peace Spice piece. Beiste is used for simulation and then lastly, you go to the peace of the Layup process, which is handled by PCB editor. Now, with an understanding of how capture, piece Bites and PCB editor are integrated into the PCB design process for a schematic simulation and PCB layout, you'll know exactly which software to use during each phase of the PCB design process 3. OrCAD Trial vs OrCAD Lite: Hi. I want to explain the difference between or cat light or piece by slight and or cat trial. So when you go out or cad or cadences website, you can see the free or cat like download. You sign up, then put in your information and you can download the light version for free. What's good to note about the orchid light version is that you only get 75 nets or less in your project, so your project needs to have 75 or less notes, nets and things like that. It also needs toe 100 or less parts in the project, so you can only stick to simple designs. Now you can get the or cat free trial or the peace buys free trial. They are the same thing. They'll both take you to start your free or cap trial today. The same page, and what's good to note about or cat Trollope Spice trial is that you can handle designs larger, then 75 nets or greater than 100 parts. You only get to do that for 30 days, though, so if you want to build something like an Arduino clone or a huge boar designed multi layer board with multiple, like hundreds of parts or something like that, and you want the or cat trial, but you get 30 days to complete your project, and you can sign up for cat trial and the free trial for the 30 days on your computer. However, note that even if you use multiple emails or sign up for multiple trials, you get one installation per computer. They tag your device, that is cadence. The software tags your device so you only get one installation perch computer. So just a quick recap. The or CAT trial can allow you to do complex designs greater than 75 nets and greater than 100 parts in the design. But you only get that for 30 days. The orchid light allows you to do simple design center 75 nets or less, but less than 100 parts. But you get to keep it forever, so that is the difference between or cat trial and or cat light. Do not do the trial until you are ready to do a complex design with 75 or more nets well greater than 75 nets or greater than 100 parts. Otherwise, stick with or kept light. If your designs are simple enough 4. How to install OrCAD Lite: So let's get started with installing the software. Open up your favorite rap browser and you can goto www dot or cab dot com on Look under the products and or CAD light Overview. Just click on this big button here, and it will take you directly to the or cap for free link. And to your information on. The most important thing is to look under the software requested section. Make sure you choose the first option. Here. It's the workout 17.2 PCB Designer Light all products Download option Now You could request it to be on a DVD, but I I wouldn't recommend that. If you're trying to get this started as soon as possible, just download. Make sure you have a suit. Ah, good, solid connection on Wait for them to send you an email. You wanna click, submit and wait for that email. Then when you get that email, it will just be a short link. Click on it and then you'll start the software download. Once you actually download the software. It's in a ZIP file, but it's pretty big. 1.7 gigabytes large. Okay, once you've downloaded the software, you wanna right. Click it, then choose extract. All okay. When you choose extract all it will open it out. No new folder or whatever you want to name it. And I just chose to go with the default folder name here, and it created the folder within here. And you want to right? Click this set up dot txt file and run as administrator. Hopefully, you do have administrator privileges. You will need that on your machine, or it is preferable. But if you don't have administrative privileges, but you're able to install software than that should work too. So just make sure you open it and run the software. Now, this won't work for me because I already have it installed along with the full design suite package, along with the professional version as well. So have a lot of stuff installed in here. And that's why I'm getting this error. But for you, everything should go just fine with the insulation. Once the insulation is finished, you're ready to get started with capture C. I s light for your schematic printed circuit board 5. Creating and Simulating a schematic in Capture CIS Lite: Hello. Welcome back. And in this video, I'm gonna show you how to make your first schematic simulation and printed circuit board in the capture C. I s Light and PCB editor software suite. So let's go to the start menu here and she's all programs next gonna scroll down to the cadence. Really? 17.2 folder. I have a lot of software packages installed here under this cadence. Really? 17.2. So just ignore these folders here. Now, what you should have is just that work at Light Products week. So I'm gonna go on or cat light here, and you should have captured C. I s like, So click on that. This is a software tool that's going to help you create your schematic or you're drawing for your led. So go to file new project the name it led. Make sure it's a piece spice, analog or mixed a D option for your project here that allows it toe be simulated. Now under location. Click the browse button here. I'm just gonna put this project in the documents folder. So click new folder. I'm gonna name it Led. Go into the folder here, select it then click. OK, I'm gonna create a blank project, So make sure create a black project here and click OK again and capture CIA's will load a new schematic page for you to put your circuit onto. Now there's a lot going on here, but there's a lot of things that you don't really need to know. I'm just a few things that you do need to know to get your schematic made. First, it's the part place option. So go over here a quick access toolbar and choose place part or hit P on your keyboard for short that will open up the place. Part window on. Do you want to type in? Are for resistor. Now that shows up here for me because I already have this library at it. But in case you don't have that library, if it's your first time using the software, look under libraries here and then choose the Eid library option. Are is any analog folder and that would be this right here. This is a library, and I'll explain this later on in the course. But these air libraries that house the parts that you need to choose analog got oil be, and when you type are in the part search field, it shows up it. Enter in a keyboard so it gets attached to your cursor. All right, now I want to rotate this parts or right click. Choose, rotate it, rotate, sit there and just click once a place it onto the schematic next one out of E. D. C. It doesn't show up on. That's because I don't have the library selected. That would house the VDC. In case you don't have the library, either. Just click on add library and then that would be under sources. So let's just look for the source library sore start oil be click open and VDC appears. So this is Ah, DC voltage source, so just hit. Enter on your keyboard. Click wants to place it on the schematic right click and choose and mode, or you can hit escape on the keyboard. Next, I want to add an led, so I wanna just select all of these libraries that I do have. In case you don't have these, click on the Add libraries button, click once on any one of these libraries and hit control A on the keyboard and choose open . Well, this does it. Adds all those libraries in that folder into this libraries section here. Sometimes they're not all selected, so just click once on one of them than hit control A on your keyboard to select all the libraries. Okay, let's look for led. Now. LFT shows up under the discreet library option, but I'm not sure if I can actually simulate this. Led on. Also, sometimes the led option won't even appear if you don't have, ah, certain libraries available to you. So I'm gonna show you how to look for a part that you don't know the part Number four or don't quite know the name of Got a place piece by its component search. Now the piece by his part search window appears. And I want to look for an led under the optoelectronics device. Expand this folder. Also expand. Led. He's gonna go with a five millimeter t 10.75 package twos. Amber, I click once on this first option than double click for it to attach to my cursor. Why am I going through all this? It's because I know for sure that when I used the, uh, place piece by component option that the device can be simulated with these other libraries . They may not necessarily be simulate herbal, which is not a reward. But you get the idea. You may not be able to simulate those parts. So this is the method I like to go with, right? So are on your keyboard to rotate it, place it right onto the resistor there, right click and choose and mode. I'm gonna close this window and then add one more thing, which is a ground component here. She can either hit G on a key border. Click place ground on a quick access toolbar and go with zero capsule or zero source. Either one is fine and click. OK, place it right under the led right click and choose and mode. Now it's time to wire the components. So click place wire and then click release to make your vergis ease and your connections. All right, so just be very careful when you're connecting these components. Okay, so I made a mistake here and wire. Whenever you make a mistaking, just click drag and hit delete on your keyboard, and that will delete the extra wire. So to file and save your project. I'm going to change the values. So for the resistor, double click on the one k changing to 500 could enter for the V one device or this. Ah, DC voltage source change up to nine volts. DC click. OK, I'm gonna simulate this circuit out of voltage marker between the resistor on the die out here. So I'm gonna place this v voltage marker, right? And between those components this week for it to load. OK, right click and choose and mode. Now, in case you don't have this toolbar, you can guess Goto api spice markers, bolted level. And then this is where you can find the markers that you want. You can take a differential voltage between circuit components or a voltage from that point to ground. So there's a lot of options here for markers. So what this voltage probe is going to show us is the voltage between these two components with respect to grout on? It will always do that wherever point your placing it on to it. Take the potential from that point to ground. Okay, so now let's set up a piece by simulation profile gotta pee Spice new simulation profile. And I type in something like D c transient because we're gonna show the progression of the voltage over time. Click, create and click on this little window that pops up here. And this is the simulation settings and P spice for the analysis type. Choose time domain set the runtime toe. One second said the maximum step sizes 0.1 click. Apply, then. Okay, Now the probe disappeared. That's interesting. Okay, so you want to make your probe markers? Wanna play some onto the circuit? After you've created your simulation profiles? Let's place a probe again. P spice markers. Welders level right there. Okay, right. Click. Shoes and mode. Now you're ready to simulate. We're gonna pee spice again. Then click the run button. And now this window shows up on the bottom. This is the piece Spice simulator window. Okay, The voltage remains the same over the course off. Who? One second and it's just under two volts. Now, where is that voltage? Like I mentioned earlier, it's the voltage between this point and ground. So there's a huge voltage drop here of seven volts from this Ah nine vote vdc device here. Okay. It's pretty big. Drop foot. That's fine. Now that you simulated the circuit, I'm gonna show you in the next video. How to create the PCB from you're led schematic. See you in the next video. 6. Footprints and Setting PCB Parameters: Hello. Welcome back in this body. I'm gonna show you how to transfer your schematic You created and capture. See a slight toe, a PCV and PCV editor light. So have capture. See, I asked open with your project available to you and click the project type over here. That's named led 0.0 P. J. Next, you want to expand these folders here? This is the design file, and this is thes schematic page. They want to rename this. So just right, click the schematic folder and choose Rename. We're gonna change the name to led SCH or Schematic and hit. Enter on the keyboard. Next. You want to change this page? Name So right, click and rename it to the same thing as your folder here led sch hit Enter. What I'm gonna do is duplicate this circuit onto a new schematic so that I can leave the simulation alone here. And I just create a new schematic that what I would use for mechanical purposes because you have to make some modifications to it. So back in the project tab here, right, click on the design file, then choose new schematic. Let's name it led PCB It had enter. Now, right click the led SCH schematic file. We'll choose. Copy. Recollect this new folder led PCB. Choose paste, expand this folder. I noticed that the led schematic page has been duplicated onto this new folder. That's good. Go back to the project tab. Let's rename it because it can get a little confusing when you have a lot of schematic pages. So right, click on, choose to rename the schematic page. We'll name it. Led PCB. Okay. All right. The last thing that needs to be done is I'm gonna close thes pages, so right, click and close them. Okay? You want to right? Click this led PCB folder and then choose make route. This will be the focus of our PCB. So double click on led PCV now, and we're gonna work with this circuit degree, the printed circuit board and PCB editor light. So first things first, you need to delete this V d. C. Here. This is just for simulation purposes. You actually need riel connectors to connect to the schematic. So click drag and highlight this along with the wires hit, delete on your keyboard, and then that disappears. Next thing you need is to add a connector. So in the place part option. If you don't know how to get here, just let me show you. I'm gonna close this window. All right? So if you don't know how to get to the place part option, just click on place part or attack P on your keyboard. All right, so we're gonna add a connector. Now, I know the library components from memory, and I've done so many designs in the software. I know it's named CEO end one, but it doesn't show up whenever this happens, and it doesn't show up. You need to know the library of the part is available in, so click on the add library button. Now, by default, I've been a piece spice folder. Gonna click the drop down menu here. Andi, Let's go to the cadence. 17.2 folder under their tools. Capture library. I'm gonna go one above the piece. Spice folder. The connector I'm looking for is in the connector. Daughter will be libraries and click on it and choose O'Berry shows up on a connector con. One is now visible. So double click on con one and place it right onto the circuit here. Make sure this red dot shows up. That was a caution. Simple here, but don't worry about that. Click and place it. Place the other one here. Right click and choose and mode. Now we have physical connectors that would connect to your PCB. Next we need to do is just go to file safe. Make sure that's, uh, in good order there. Now click Dragon hold and select all these components. Goto in it. Properties, make sure in the lower left you have the parts top selected here. Also, click Dragon hold or click. Hold on track to the right so you can see the reference numbers for your components. Lastly, let's drag this, uh, bar here to the right until we see PCB footprint in this color. Now there's already a footprint name associated with the resistor. I'm just gonna go ahead, delete that. So click it hit. Delete on keyboard on your gonna use some PCB footprint names that already in the standard libraries when you install the software. So for resistor type in our yes, 400 for the connectors. We'll use jumper one. Not for the led. I found a pretty complicated name for the for footprint for this part. So I put a note pad here, and it's a really long name, just real pre deposit video. So you can type this in or save it somewhere. All right, so with this footprint name, just double click and right click. We're gonna copy it, put it right in the piece of your footprint field for the diarrhea hit Control V on your keyboard to paste it. And there you go. Right. Click this tab here and choose safe so that the schematic is safe properly. Now go back to your schematic tab and all your parts. How footprint associated with it. Next thing you want to do is go to the project tap and make sure led PCB is still your root folder. Click on the led PCV schematic. Choose tools create net list. We're gonna transfer the schematic to a printed circuit board, so choose create eight or update PCB editor board, not Net, ref. And just before we do this, I'm gonna show you how to set up your PCB editor Environment and PCB Editor Light. So go to your Windows Start menu. All programs kids really 17.2 have a lot of folders. Hair you may not under the or cattle light products and shoes. PCB Editor Light gonna enter light mood. Okay, Now how do you set up a new PCB? Well, just go to file new choose the board wizard on a name it led PCB. But the browse button I'm gonna place this PCB inside the project folder that I'm working in right now. So go toe libraries, documents It's going to navigate to the led folder. I'm gonna make a new folder to soul. It's It's a name it Ah Allegro All Lower case hit. Enter on the keyboard, go into the Allegra folder and select. Open. Now click OK on the wizard starts. So just keep looking next until you get to the option where it asks you about. Let's see here The spacing constraints said the minimum lying with the 20 milks or 20,007 inch the default via pad stack. You have to select one here, so click on the Ellipse sees on and tightened via hit tab on your keyboard. I'll go with the Viet 26 actually click, OK, and then hit next. Now I want a rectangular board. So I'm gonna see you choose that click next again. The 1000 mill wit on height here is more than enough space for what I need s So I'm just gonna stick with that. And she was next. Then finish. All right, So the outline of your printed circuit board has been made in the next video. I'll show you how to continue this PCB designed process in PCB Editor light. 7. Routing the PCB: Oh, right. Welcome back in this video. I'll show you how to take your PCB environment that you just set up in PCB Designer Light or PCB Editor light. I'm schematic that you've created here and capture C. I s light. Not a transfer. You schematic to the actual PCB Larry components and get your peace be designed here. So what you want to do is make sure you have capture C I s light open with your project. Open on right now. I'm gonna create net list option. We're just I'm just gonna close this. I'm sure you had to get back to that in case you missed it. Does make sure you select the led PCB page on your project and go to tools. Create net list on then that window will appear. OK, so check Mark. Creator update, PCB Editor board on for the input board file. You would select the one you just made in PCB editor like So before I do that, I'm gonna close this. It acts me if I want to save. Yes. Now, remember or recall where you actually saved that PCB outline. So for the import board file, click on the ellipses here going to navigate to my folder the Led Allegro folder. And it's looking for this dot bi rd file. So click on it. She's open. I noticed the output board file is just gonna be named led dot BRT There's no need for me to create a new PCB, so I'm just gonna name it the same thing on what it will do is it will open the led PCV, then rewrite over it and then save it again with the same name. Okay, in the bottom section here. Board launching option. Make sure to choose open board and PCB editor or or cat PCBs. Look OK, now it's complaining about not having a full licence for this. Solve this into the light mode. Yes. Okay. This PCB environment looks exactly the same. So what's changed? Right. Well, what's happened is that the components that were in the schematic here have been placed into the environment for your PCB editor or your PC be here. So the place components manually. Then check mark all of these. So you want to check mark that components by raft dasa box so all the parts gets elected. Hide this window by clicking the hide button. Now I'm gonna place de one. This is the dialogue or led if you will, right? Click and should rotate. That will rotate the component left click to continue placing it. I'm gonna place it right here. Notice how the other connector or component attacks is to my cursor automatically. Whenever I placed one, I'm gonna police it right here. Places other connector here on. Lastly, I'll put this resistor right across from here. Great. Now I want to rotate this d one device. So to do that, I have to pick it back up. Click left. Click on it once. Right. Click, rotate. Just move it around until it's rotated the way I wanted to. And click wants place right here. Let's see if I can lined it up. All right, that's that's pretty OK, we're gonna try to line up this here. Okay? It's good. I kind of lineup this last connector here. Great. Everything's lined up nicely, but I'm still in part placement mode. So after right click and she was done. Very good. Goto file save. Yes. Next thing you want to do is to wire these components just like you did in capture C I s like so it's really simple. Just got a route. Connect, Click Once on this path, stack here and then just move your cursor along to the left. Do not click holding track. Just click. Release on the wire will follow wherever your cursor is going. Click wants to place that connector there. Continue this process to connect these other pins and pat stacks. And there you go Now, right click and she's done. All the components are connected together. Make sure you goto file and say quick. Yes, Sometimes the software can close on its own. It happens very rarely, but whenever that does happen, you want to make sure that your project is safe. 8. Gerber and Drill: Now I'm gonna show you how to create the Gerber or artwork files and send them to a fabrication house. So go to export and choose the Gerber option here Now top and bottom already selected. That will be the top cop earlier on the bottom cop. Earlier for your PCB, it's cook on top, said the undefined lying wit, too. 10 mils. Okay, care and then set the bottom two 10 mills with under fire line with us. Well, why are we doing that? It's because the PCB editor like software automatically sets zero to the undefined language . It's on zero languid zehr really weird, and they don't take well in Gerber organization our creation. So just keep that in mind. Select the apertures button shoes at it, auto without rotation and notice the 20 new opera Cher's air created here. Look. OK, look okay on this one. No. And shoes select all. Then hit the create artwork button. Now you'll usually get warnings whenever you create your artworks. But just make sure you check through this file and then it shows in a summary that the top was actually created on the bottom was created. If it was with warnings. That's that happens pretty often. So close this window and click. OK, go file and then save one more time. But yes. Now I'm gonna show you how to submit these files toe aboard house. But there's one more thing you need and that's a drill file. So goto export and see drove NC parameters. Check mark this leading zero suppression option and this other option here with enhanced excellent form and could close had the scale factor toe one. So, like these two options on uncheck repeat coz then click drove close your window drove was just created and we're gonna double check to make sure that the art files on the draw If I was actually created. Close this window. Save one more time. Yes, Go to the folder where you created your project For me It's in documents led allegro and for the type of file I'm looking for my art files says bottom dot art Top that art. Those got generated. That's good. The drove five als also generated really good over right? So click on the bottom that art hold down control key on your keyboard. Here, click and select the top That art file and also the d r L file. You want to right click and I have seven zip installed, So I consented to that compressed folder. But if you don't have sevens, if you could just go to send to and shoes compressed Zip folder that's installed by default in Windows, I have to name this file. I'll name it. Led heart hit Enter and I'm gonna upload this file to a website that allows me to fabricate PCBs through them. So I'm gonna open up a Web browser here. It's got a Google chrome. Okay, I was gonna type in a Web site like four PCB dot com. Enter on the keyboard. Now, under their products and services, you can choose the free DFM tool, and this is really neat. It shows you, if you would have any problems or potential issues with your PCB. When you submit your API should be designed to them so could upload files. I'm gonna set my email here. Just type in that information so that choose file. Go back to your Project folder in the Allegra folder here, and that's where I saved my led art that zip file so select it. She's open. Upload. Zip file. Now you have a lot of options to choose from this next window, but you have to send everything correctly. So I'll show you that in the bottom down art file here, I'm going to set this file content. Option two. Bottom copper. The top That art is my top cop earlier. So I'm going to set that to top Copper. Now it's automatically detected in my trow file, probably because of the extension here, because it's chosen and Seadrill and that's correct. Great. Now let's go with a company name here. Let's call it imaginary company Phone number 777777777 It's not a real number. I don't know whose number that is, but it's something for the court number. I will name it led. You see me? The revision one said the layer count to two. Why, too? Because the top layer on the bottom there count is two copper layers. So it's the copper layers that we are counting here. The X dimension said it the one that's in inches Now that's the same as 1000. Uh, Mills. Okay, so if you remember when we set up the PCB environment and PCB editor like you chose 1000 mills for the with the night. So it's Wantage. Okay, one inch. Most of the options here are pretty good, but there is no sauder mask, so I'm gonna choose none. There's no silkscreen, so go with none there, too, on the color and whatnot. So relevant because the sauna mass silkscreen aren't there. Next, Want to go with a i t. A r option set to know that's pretty much everything for this submissions. Click Submit on. Do you get this window? Once you're PCV artwork, files have been submitted. Next thing you want to do is wait patiently for your results to show up via email. Now that can take anywhere from 10 to 30 minutes. Eso I would recommend maybe getting a cup of tea year coffee or going on or doing something else. When you check your email in about 30 minutes or so, then you'll get to see your results and I'll show you that 9. Recap: All right, Welcome back. You finish your first PCB and capture CS Light and PCB Editor lights A really good job. You would have got an email from four PCB dot com on what your printed circuit board actually looks like. So open up the email from results at four p c v dot com. Let's go down and click on the link here That's next to the DFM results. When you click on it, it will show if you have any showstoppers or problems that needed some fixing there. No tweaks or any problems here. So really good you're going to close this window. You can also see the plots for your Garber files. So if it's difficult for you to, uh, generate plots for your PCB here and piece of theater like you can just click on this link and they'll show you the files that were generated. So, for instance, your top that art file looks like this. Your bottom dot art file will look like this on your profile. Well, look, something like this. Now, I ran into a problem with my drill file that to regenerate it as per the instructions in the previous video So if you have the same problem, just go back to the previous video and regenerate your TRO file. Andi, you will correct it to make sure that it is correct. You want to go to www dot Gerber hyphen viewer dot com and in this choose your files and upload them one by one and you have all of them. Check mark. You'll find that your new deadly generated drove file actually overlays quite nicely right into the patch stacks and pins of your opponents. So, yes, if you have her up that situation, just regenerate the drill file and you'll be fine. Okay, so that's pretty much everything I wanted to show you for your first PCB and capture. See, I asked lighting peace, be it under light. I'm gonna explain the environment Capture. See, I asked, I'm PCB editor and in addition also, you have pout stack editor works. You need to know all this detailed information to understand how to make a PCB in depth on . We'll use that information to create a second printed circuit board. So stay with me, really excited to show you everything about this powerful tool that you can use to make amazing PC bees in no time